Daewoo Head Gasket repair made easy

There are differences between engines on the exact process and components, but the typical engine will require most of the following basics to be done

• Mechanic will check that the head gasket is faulty.
• The engine will be drained of oil and coolant.
• Components will be removed to allow access to the rocker cover and ultimately, the cylinder head bolts.
• The engine timing will be locked in place using specifically designed pins and locking tools.
• The timing belt will be removed, or the timing chain loosened off and moved off the camshaft sprockets.
• The cylinder head will then be undone in a specific sequence.
• Once all the bolts are out, the cylinder head will be removed and the surface of the engine block and cylinder head will be cleaned of all residue of the old gasket.
• In the case of the majority of cylinder heads, it will need to be pressure tested to ensure it’s structure is sound and then go through a process called skimming. This process ensures that the surface that the new gasket will come into contact with is perfectly flat and clean.
• Once the mechanic has completed the work on the components, the engine is reassembled with a new cylinder head gasket.
• If the engine’s camshaft(s) are driven by a timing belt, this belt will be renewed along with a new water pump if it is on the timing belt circuit.
• Once the engine is back together, the cooling system will be refilled and the oil replenished along with a new filter.
• If the oil has become contaminated with the coolant, an additional oil flush may be required and likewise, if the cooling system has become contaminated, the cooling system will be flushed.
• Once everything is back together, the mechanic will run the engine.
• Finally a road test will ensure that everything works as it should when the engine comes up to temperature and finally any error codes present will be cleared down and re-checked.

As we mentioned previously, this is not a full exhaustive list of what will be done as each engine has its own requirements.

In most cases the symptoms of a cylinder head gasket are pretty apparent, some however take a little know how and some tools to confirm. Typical symptoms though are;

• A cream-like colour and consistency in the oil (usually seen on the engine oil dipstick) or in the cooling system header tank.
• Coolant overflowing out of the cooling system header tank.
• An unexplained loss of coolant.
• Difficulty in starting the engine.
• Evidence of exhaust gasses in the cooling system.
• Poor engine compression.

The time it takes to carry out a head gasket replacement can range from 5 hours to more than a day. Ultimately, the time that the job will take will depend on a number of factors, like your vehicle's make and model, year, type of engine, as well as other factors. Select your car at the top of this page for information on job time and cost for your vehicle through ClickMechanic.

As soon as the efficiency of the cylinder head gasket is compromised, the gasket needs to be replaced prior to the engine being used again.

If the oil and coolant has mixed, the lubricating quality of the oil is non existent and its ability to preserve the internal parts of the engine is lost. Continuing to run the engine will ultimately end in severed damage to it. The same goes for the cooling system, with the water channels and radiators becoming blocked. If the coolant is being lost, the engine will overheat. This is not good for the metal components of the engine and the aluminium cylinder head could be damaged beyond repair.

Whilst cylinder head gasket replacement is not as common as it was 20 or so years ago, it still occurs. Certain engines are prone to it happening and the use of smaller engines with turbochargers puts increased pressure on the gaskets.

To help prevent head gasket issues:
* Regularly check and top up the coolant level as required
* Follow the manufacturere recommended service schedule
* Inspect the engine regularly for leaks, to spot any issues early. If you see any, have them repaired as soon as possible.

Common signs of a bad cylinder include:
* Loss of power
* Poor engine performance
* Coolant leaking
* Overheating of the engine
* Smoke (from tailpipe or from cylinder head itself)

While the cost of the head gasket might not be much, the work involved to fix or replace it requires a lot of time and effort which is why the cost can be quite expensive. Whether it is worth replacing or not depends on the value of the vehicle. If the vehicle is old and the cost of the replacing the head gasket is more than the value of the car then it's best to sell or scrap the car.

Repairing a head gasket can cost anywhere from £500 to over £2000 depending on the make and model of the car. Most of the cost is attributed to labour as the process can take 8-10 hours as it requires the mechanic to disassemble the top of the engine, and in some cases may have to remove the engine from the car.

The first signs of a blown head gasket are usually:

• Steam and/or water coming from the tailpipe
• Overheating
• White smoke coming from the tailpipe
• Loss of power

Yes, many local garages are able to offer collection and delivery for a head gasket repair on your Daewoo. With ClickMechanic collection & delivery is free if your vehicle is drivable. Once booked a mechanic will pick up the vehicle on the day and time of your choice, do the work, and return the vehicle at a time convenient to you. Simply enter your vehicle registration number and postcode to get an upfront price for a head gasket repair on your Daewoo.

Typically no, mobile mechanics cannot do a head gasket repair at your home or office on your Daewoo, because the repair may need to be carried out on a ramp, and may need specialist equipment. Also, the time involved to carry out the work may make it more practical to carry out the work at a garage. However, if there are still some doubts as to what repair is needed, mobile mechanics may be able to carry out a diagnostic inspection at your home or office on your Daewoo and then take the car to a garage to carry out the head gasket repair.